This website is not affiliated with or sponsored by Crown. To purchase Macro-Tech 5000VZ spares or accessories, please contact the company via their website or visit an authorised retailer. Manual Library / Crown. Crown Macro-Tech 1200. Professional Stereo Power Amplifier. Macro-Tech 2400. Macro-Tech 3600VZ. Gallery Images. This website is not affiliated with or sponsored by Crown. To purchase Macro-Tech 1200 spares or accessories, please contact the company via their website. Jul 05, 2017 crown macro tech 2400 owners manual tutorial Free access for crown macro tech 2400 owners manual tutorial to read online or download to your computer. Read these extensive report. View and Download Crown Macro-Tech MA-2400 service manual online. Crown Macro-Tech MA-2400: Supplementary Guide. Macro-Tech MA-2400 Amplifier pdf manual download. Crown Macro-Tech MA-2400 Pdf User Manuals. View online or download Crown Macro-Tech MA-2400 Service Manual, Reference Manual, Schematic Diagram.
- Crown Macro Tech 1200 Specs
- Crown Micro Tech 2400
- Crown Macro Tech 1200
- Crown Macro Tech 2400 User Manual Pdf
Advertising
Macro-Tech 600/1200/2400 Power Amplifiers
Crown Macro Tech 1200 Specs
Page 14
Reference Manual
3.3.4 Input Connection
Both the balanced XLR and phone jack inputs have a
nominal impedance of 20 k ohms (10 k ohms with un-
balanced wiring) and will accept the line-level output of
most devices. Female three-pin XLR input connectors
are provided on the standard P.I.P.- FX input module
(other PIP modules are described in Section 8.1). Cor-
rect input wiring will depend on two factors: (1) whether
the input signals are balanced or unbalanced, and (2)
whether the signal source floats or has a ground refer-
ence. Figures 3.7 and 3.8 show the recommended con-
nection techniques for each type of signal source.
Both the balanced XLR and phone jack inputs have a
nominal impedance of 20 k ohms (10 k ohms with un-
balanced wiring) and will accept the line-level output of
most devices. Female three-pin XLR input connectors
are provided on the standard P.I.P.- FX input module
(other PIP modules are described in Section 8.1). Cor-
rect input wiring will depend on two factors: (1) whether
the input signals are balanced or unbalanced, and (2)
whether the signal source floats or has a ground refer-
ence. Figures 3.7 and 3.8 show the recommended con-
nection techniques for each type of signal source.
The amplifier’s built-in ¼-inch phone jack input connec-
tors can be wired similarly for balanced or unbalanced,
floating or ground-referenced sources. They have a
tors can be wired similarly for balanced or unbalanced,
floating or ground-referenced sources. They have a
![Crown Macro Tech 2400 User Manual Crown Macro Tech 2400 User Manual](/uploads/1/2/6/1/126196099/780072109.png)
Fig. 3.7 Unbalanced Input Wiring
Fig. 3.9 Balanced and Unbalanced Phone Plugs
Fig. 3.8 Balanced Input Wiring
standard tip-ring-sleeve (TRS) configuration: the tip is
positive (+), the ring is negative (–) and the sleeve is
ground (see Figure 3.9). Wiring for various sources fol-
lows the XLR wiring guidelines shown in Figures 3.7
and 3.8.
positive (+), the ring is negative (–) and the sleeve is
ground (see Figure 3.9). Wiring for various sources fol-
lows the XLR wiring guidelines shown in Figures 3.7
and 3.8.
Crown Micro Tech 2400
The phone jacks should not be used as inputs when a
PIP module with active circuitry is installed. The phone
jacks are in parallel with the output of the PIP module,
so an input signal connected to the phone jacks can
feed backwards into the active circuitry of the PIP and
cause undesirable distortion. You can use the phone
jacks for signal input with any of the following PIP mod-
ules installed: P.I.P.-FX, P.I.P.-BB, P.I.P.-FMX, P.I.P.- FXQ
and P.I.P.-FPX. All other PIP modules have active cir-
cuitry and should not be installed if you plan to connect
input signals to the phone jacks. The phone jacks can
always be used as “daisy chain” outputs to feed post-
processed signals from the PIP to the inputs of other
amplifiers.
PIP module with active circuitry is installed. The phone
jacks are in parallel with the output of the PIP module,
so an input signal connected to the phone jacks can
feed backwards into the active circuitry of the PIP and
cause undesirable distortion. You can use the phone
jacks for signal input with any of the following PIP mod-
ules installed: P.I.P.-FX, P.I.P.-BB, P.I.P.-FMX, P.I.P.- FXQ
and P.I.P.-FPX. All other PIP modules have active cir-
cuitry and should not be installed if you plan to connect
input signals to the phone jacks. The phone jacks can
always be used as “daisy chain” outputs to feed post-
processed signals from the PIP to the inputs of other
amplifiers.
Crown Macro Tech 1200
Please follow the instruction in Section 3.3.2 and 3.3.3 if
the amplifier will be used in either Bridge-Mono or Par-
allel-Mono mode. Remember, do not use the Channel 2
input in either of these mono modes.
the amplifier will be used in either Bridge-Mono or Par-
allel-Mono mode. Remember, do not use the Channel 2
input in either of these mono modes.
Advertising
![Macro Macro](/uploads/1/2/6/1/126196099/165792823.jpg)
Popular Brands
Crown Macro Tech 2400 User Manual Pdf
Popular manuals